5.3 KiB

Raw Permalink Blame History

Network

Home Assistant Operating System uses NetworkManager to control the host network.

Configure network

By default the device will be in DHCP state.

Basic network settings can be set through the Supervisor frontend in the System tab. Advanced configurations such as VLAN are also available through the ha network CLI command.

To restore the default configuration the ha network CLI command can be used as well:

ha network update default --ipv4-method auto

If more advanced network settings are required network connection files can be placed on a USB drive and imported to the host as described in Configuration.

Manual Network Configuration

If the frontend or ha network CLI cannot meet your use case, it is still possible to configure the underlying NetworkManager manually.

You can read the NetworkManager manual or find many configuration examples across the internet. Note that changes to NetworkManager.conf are not supported currently, only connection keyfiles are supported. Keep in mind that the system is read-only. If you don't want the IP address to change on every boot, you should modify the UUID property to a generic UUID4. Inside the \CONFIG\network\ directory on the USB drive or SD card, create a file called my-network and add the appropriate contents below:

NOTE: Please make sure to save this file with UNIX line endings (LF, and not Windows' default CRLF endings). You can do this using Notepad these days!

Default

A preinstalled connection profile for wired network is active by default:

[connection]
id=Home Assistant OS default
uuid=f62bf7c2-e565-49ff-bbfc-a4cf791e6add
type=802-3-ethernet
llmnr=2
mdns=2

[ipv4]
method=auto

[ipv6]
addr-gen-mode=stable-privacy
method=auto

Wired connection to the LAN

[connection]
id=my-network
uuid=d55162b4-6152-4310-9312-8f4c54d86afa
type=802-3-ethernet
llmnr=2
mdns=2

[ipv4]
method=auto

[ipv6]
addr-gen-mode=stable-privacy
method=auto

Wireless LAN WPA/PSK

[connection]
id=my-network
uuid=72111c67-4a5d-4d5c-925e-f8ee26efb3c3
type=802-11-wireless

[802-11-wireless]
mode=infrastructure
ssid=MY_SSID
# Uncomment below if your SSID is not broadcasted
#hidden=true

[802-11-wireless-security]
auth-alg=open
key-mgmt=wpa-psk
psk=MY_WLAN_SECRET_KEY

[ipv4]
method=auto

[ipv6]
addr-gen-mode=stable-privacy
method=auto

Static IP

Replace the following configuration:

[ipv4]
method=manual
address=192.168.1.111/24;192.168.1.1
dns=8.8.8.8;8.8.4.4;

For address, the value before the semicolon is the IP address and subnet prefix bitlength. The second value (after the semicolon) is the IP address of the local gateway.

Tips

Reset network

If you want to reset the network configuration back to the default connection profile using DHCP, use the following commands on the host console:

# rm -r /mnt/overlay/etc/NetworkManager/system-connections
# reboot

Home Assistant OS will recreate the default connection profile during boot.

Enabling Wi-Fi

Wi-Fi is discouraged for reliability reasons. However, if you still prefer to use Wi-Fi, you can us the ha network command to set up Wi-Fi (example for a Raspberry Pi 4, check ha network info to check if your board supports Wi-Fi and the name of the Wi-Fi device):

ha network update wlan0 --ipv4-method auto --wifi-auth wpa-psk --wifi-mode infrastructure --wifi-ssid "MY-SSID" --wifi-psk MY_PASS

Powersave

If you have trouble with powersave then apply the following changes:

[wifi]
# Values are 0 (use default), 1 (ignore/don't touch), 2 (disable) or 3 (enable).
powersave=0

Using `nmcli` to set a static IPv4 address

Log into the the Home Assistant OS base system via a console:

Welcome to Home Assistant
homeassistant login:

From there you use the nmcli configuration tool.

# nmcli con show will list the "Home Assistant OS default" connection in use.
# nmcli con show "Home Assistant OS default" will list all the properties of the connection.

To start editing the configuration setting for "Home Assistant OS default":

# nmcli con edit "Home Assistant OS default"

To add your static IP address (select 'yes' for manual method);

nmcli> set ipv4.addresses 192.168.100.10/24
Do you also want to set 'ipv4.method' to 'manual'? [yes]:

In addition, it's recommended to set the DNS server and the local gateway. For most home routers the DNS server will have the same IP address as the router itself. If you are using Pi-Hole or a third-party DNS system then you can set the DNS server to that.

nmcli> set ipv4.dns 192.168.100.1
nmcli> set ipv4.gateway 192.168.100.1

nmcli> print ipv4 will show you the IPv4 properties of this connection. With nmcli> save you will save the changes afterwards.

If you now view the default connection cat /etc/NetworkManager/system-connections/default you should see the method is manual and the address is set.

Doing a nmcli con reload does not always work, so restart the virtual machine or the physical system.

5.3 KiB Raw Permalink Blame History