mirror of
https://github.com/mpv-player/mpv
synced 2024-08-20 08:55:06 +02:00
2e84934be7
cehoyos adds the step_property command in7a71da01d, and it could be argued that copyright of this still applies to the later add/cycle commands (a668ae0ff9). While I'm not sure if this is really the case, stay conservative for now and mark these commands as GPL-only. Mark the command.c code too, although that is not being relicensed yet. I'm leaving the MP_CMD_* enum items, as they are obviously different. In commit116ca0c768, "veal" (essentially an anonymous author) adds an "osd_show_property_text" command (well, the commit message says "based on" that person's code, so it's not clear how much is from him or from albeu, who agreed to LGPL). This was later merged again with the "osd_show_text" command, and then all original code was removed in commit58cc0f637f, so I claim that no copyright applies anymore. (Though technically the input.conf addition still might be copyrighted, so I'm just dropping it to get rid of the thought.) "kiriuja" added2f376d1b39(sub_load etc.) andbe54f4813(switch_audio). The latter is gone. I would argue that the former is fully rewritten with commitsb7052b431cand0f155921b0. But like in the step_property case, I will be overly conservative for now, and mark them as GPL-only, as this is potentially shaky and should be thought through first. (Not bothering with the command define/enum in the header, as it will be unused in LGPL mode anyway.) keycodes.c/h can be GPL, except for commit2b1f95dcc2, which is a patch by someone who wasn't asked yet. Before doing something radical, I will wait for a reply.
50 lines
959 B
Plaintext
50 lines
959 B
Plaintext
|
|
# This file contains all bindings that were removed after a certain release.
|
|
# If you want MPlayer bindings, use mplayer-input.conf
|
|
|
|
# Pick the bindings you want back and add them to your own input.conf. Append
|
|
# this file to your input.conf if you want them all back:
|
|
#
|
|
# cat restore-old-bindings.conf >> ~/.config/mpv/input.conf
|
|
#
|
|
# Older installations use ~/.mpv/input.conf instead.
|
|
|
|
# changed in mpv 0.25.0
|
|
|
|
I show-text "${filename}" # display filename in osd
|
|
|
|
# changed in mpv 0.24.0
|
|
|
|
L cycle-values loop "inf" "no"
|
|
|
|
# changed in mpv 0.10.0
|
|
|
|
O osd
|
|
D cycle deinterlace
|
|
d cycle framedrop
|
|
|
|
# changed in mpv 0.7.0
|
|
|
|
ENTER playlist-next force
|
|
|
|
# changed in mpv 0.6.0
|
|
|
|
ESC quit
|
|
|
|
# changed in mpv 0.5.0
|
|
|
|
PGUP seek 600
|
|
PGDWN seek -600
|
|
RIGHT seek 10
|
|
LEFT seek -10
|
|
+ add audio-delay 0.100
|
|
- add audio-delay -0.100
|
|
( add balance -0.1
|
|
) add balance 0.1
|
|
F cycle sub-forced-only
|
|
TAB cycle program
|
|
A cycle angle
|
|
U stop
|
|
o osd
|
|
I show-text "${filename}"
|