control. Possible values are top, center, and bottom,
with bottom being the default. Alignment is relevant when
it comes to positioning subtitles with one line (or fewer
lines) of text relative to multi-line subtitles.
It is implemented as a new command (sub_alignment) that
without an argument cycles the alignment (between top,
center, and bottom), or with an argument sets the
alignment (0 for top, 1 for center, 2 for bottom).
The key 'i' is bound to this command.
patch by Oskar Liljeblad (oskar@osk.mine.nu)
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8535 b3059339-0415-0410-9bf9-f77b7e298cf2
with it. These are:
1) current code is messy
2) poor comments, if any
3) inaccurate frame dropping and delay code
4) output filename hardcoded
5) output framerate as integer
You may specify the output filename and framerate like so:
-vo gif89a:4.33 4.33 fps output
-vo gif89a:some.gif output to some.gif
-vo gif89a:5.02:new.gif output to new.gif at 5.02 fps
The filename defaults to out.gif, and the framerate defaults to 5 fps.
by Joey Parrish <joey@nicewarrior.org>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8515 b3059339-0415-0410-9bf9-f77b7e298cf2
based on patch by Dominik Mierzejewski <dominik@rangers.eu.org>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8452 b3059339-0415-0410-9bf9-f77b7e298cf2
the test of a gnome class windomanager hints, since the gnome hints
are outdated and replaced by the newer NetWM specification. Newer
versions of Gnome support this standard, and therefore the test should
be placed before the Gnome test. Windowmaker does not support NetWM
and is checked after the NetWM test. In fact the new code should be
placed also before the test for IceWM. Regarding other WMs such as
KDE, IceWM the change is not tested.
patch by Svante Signell <svante.signell@telia.com>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8389 b3059339-0415-0410-9bf9-f77b7e298cf2
and store the state of XScreensaver and KDE-Screensaver, will stop them and
restart them later, when the movie has finished ...
It works and was tested with KDE2/3 and XScreensaver 4.05.
patch by Fabian Franz <FabianFranz@gmx.de>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8355 b3059339-0415-0410-9bf9-f77b7e298cf2
With only CRTC2 output all buffer setups are possible. If BES is used
only EXPORT and TEMP work. At least that's how I think it works :) IP/IPB
stuff was pretty much stolen from vo_xv.c.
patch by Ville Syrjälä <syrjala@sci.fi>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8139 b3059339-0415-0410-9bf9-f77b7e298cf2
Layer selection is done as "subdevice" - integer nuber after -vo
directfb: where -1 is autodetection and 0,1,2... are for layers
example: mplayer -vo directfb:2 -dfbopts matrox-crtc2,matrox-tv-standard=pal *.avi
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8138 b3059339-0415-0410-9bf9-f77b7e298cf2
there is /usr/local/include[/freetype/freetype.h]
and /usr/local/include/freetype2[/freetype/freetype.h] ... what a mess!
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8137 b3059339-0415-0410-9bf9-f77b7e298cf2
based on patch by Dominik Mierzejewski <dominik@rangers.eu.org>
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8124 b3059339-0415-0410-9bf9-f77b7e298cf2
Cleaned new sync code in dxr3
Renamed some internal variables to allow access from GUI
git-svn-id: svn://svn.mplayerhq.hu/mplayer/trunk@8089 b3059339-0415-0410-9bf9-f77b7e298cf2
