github/mpv
1
Fork 0
mirror of https://github.com/mpv-player/mpv synced 2024-11-11 00:15:33 +01:00
Code Releases Activity
72ef74dab5
mpv/etc/restore-old-bindings.conf

50 lines
959 B
Plaintext
Raw Normal View History

etc: add an input config file that reverts recent key binding changes This is for users who don't like changes. I'm hoping it will make the process of cleaning up key bindings less bumpy. It should be mentioned in the release notes of the next release.
2014-10-05 01:29:03 +02:00
# This file contains all bindings that were removed after a certain release.
# If you want MPlayer bindings, use mplayer-input.conf
# Pick the bindings you want back and add them to your own input.conf. Append
# this file to your input.conf if you want them all back:
#
# cat restore-old-bindings.conf >> ~/.config/mpv/input.conf
#
# Older installations use ~/.mpv/input.conf instead.
input: change license to LGPL cehoyos adds the step_property command in 7a71da01d, and it could be argued that copyright of this still applies to the later add/cycle commands (a668ae0ff90c4). While I'm not sure if this is really the case, stay conservative for now and mark these commands as GPL-only. Mark the command.c code too, although that is not being relicensed yet. I'm leaving the MP_CMD_* enum items, as they are obviously different. In commit 116ca0c7682, "veal" (essentially an anonymous author) adds an "osd_show_property_text" command (well, the commit message says "based on" that person's code, so it's not clear how much is from him or from albeu, who agreed to LGPL). This was later merged again with the "osd_show_text" command, and then all original code was removed in commit 58cc0f637f, so I claim that no copyright applies anymore. (Though technically the input.conf addition still might be copyrighted, so I'm just dropping it to get rid of the thought.) "kiriuja" added 2f376d1b39 (sub_load etc.) and be54f4813 (switch_audio). The latter is gone. I would argue that the former is fully rewritten with commits b7052b431c9 and 0f155921b0. But like in the step_property case, I will be overly conservative for now, and mark them as GPL-only, as this is potentially shaky and should be thought through first. (Not bothering with the command define/enum in the header, as it will be unused in LGPL mode anyway.) keycodes.c/h can be GPL, except for commit 2b1f95dcc2f8, which is a patch by someone who wasn't asked yet. Before doing something radical, I will wait for a reply.
2017-06-19 13:02:35 +02:00
# changed in mpv 0.25.0
I show-text "${filename}" # display filename in osd
input.conf: change "L" to change loop-file by default
2017-01-31 11:46:43 +01:00
# changed in mpv 0.24.0
L cycle-values loop "inf" "no"
inpout.conf: make shift+o toggle between 2 states only The "osd" command cycles between 4 states (OSD level 0-3), which is probably confusing and inconvenient. OSD levels 0 and 2 are rarely needed. I would claim there is normally not much of a need to completely disable OSD by setting level 0 during playback. Level 2 is just slightly less information than level 3, and I'm not sure why it exists at all. Change it so that it toggles between level 3 and 1. Note that this ignores the default OSD level. If the default is 3, the first use of this key will set it to 3 again. Just assume 1 is the default. If someone complains, this could be improved.
2015-06-03 22:02:10 +02:00
# changed in mpv 0.10.0
O osd
input.conf: remap d/D keys Drop d for toggling framedrop. Toggling this is way too special to be at such a prominent place, and in fact I believe toggling it is pointless. Remap deinterlacing from D to d. It's relatively useful and non- destructive. As suggested in #973 (almost).
2015-08-04 01:04:26 +02:00
D cycle deinterlace
d cycle framedrop
inpout.conf: make shift+o toggle between 2 states only The "osd" command cycles between 4 states (OSD level 0-3), which is probably confusing and inconvenient. OSD levels 0 and 2 are rarely needed. I would claim there is normally not much of a need to completely disable OSD by setting level 0 during playback. Level 2 is just slightly less information than level 3, and I'm not sure why it exists at all. Change it so that it toggles between level 3 and 1. Note that this ignores the default OSD level. If the default is 3, the first use of this key will set it to 3 again. Just assume 1 is the default. If someone complains, this could be improved.
2015-06-03 22:02:10 +02:00
restore-old-bindings.conf: add recently changed binding
2014-11-16 18:09:40 +01:00
# changed in mpv 0.7.0
Use - as command-name separator everywhere Old-style commands using _ as separator (e.g. show_progress) were still used in some places, including documentation and configuration files. This commit updates all such instances to the new style (show-progress) so that commands are easier to find in the manual.
2016-07-14 20:04:59 +02:00
ENTER playlist-next force
restore-old-bindings.conf: add recently changed binding
2014-11-16 18:09:40 +01:00
etc: add an input config file that reverts recent key binding changes This is for users who don't like changes. I'm hoping it will make the process of cleaning up key bindings less bumpy. It should be mentioned in the release notes of the next release.
2014-10-05 01:29:03 +02:00
# changed in mpv 0.6.0
ESC quit
# changed in mpv 0.5.0
PGUP seek 600
PGDWN seek -600
RIGHT seek 10
LEFT seek -10
+ add audio-delay 0.100
- add audio-delay -0.100
( add balance -0.1
) add balance 0.1
F cycle sub-forced-only
TAB cycle program
A cycle angle
U stop
o osd
Use - as command-name separator everywhere Old-style commands using _ as separator (e.g. show_progress) were still used in some places, including documentation and configuration files. This commit updates all such instances to the new style (show-progress) so that commands are easier to find in the manual.
2016-07-14 20:04:59 +02:00
I show-text "${filename}"
Copy Permalink